ATS ELGi Products

Paintless dents are always ignored by the customer considering the repair cost and time. Though paintless dents are less complex when compared to the normal dents ,In the current bodyshop practices the repair methodology for both paintless dents and normal dents are the same.

T HOT BOX is an innovative technology for curing soft paintless dents.

Applications

  • Suitable for all models of passenger cars , SUV and MPV
  • Paintless dent remover
  • No consumables
  • Quick reparation time
  • Less labor
  • New revenue opportunity
  • This field is for validation purposes and should be left unchanged.

ATS ELGI Alumet is a complete system for repairing body panels . It allows you to work from outside without removing the parts . It significantly speeds up the worktime and enables you to repair the original body panel without replacement. Major panel dents can be fixed using flatliner.

Applications

  • Suitable for Aluminum panel repair
  • Sliding hammer
  • Inno puller
  • Welding bits and hammers
  • This field is for validation purposes and should be left unchanged.

Dent Pulling System is used to repair minor and medium damages.
This machine has both manual mode and automatic mode.

Automatic Mode: All programs like washer welding and wavy wire welding are preset. The user has to select the required option.

Manual Mode :In this mode the user can change the power and weld time setting depending upon his requirement.

Applications

  • The machine is designed to be used both manually and to carry out automatic cycles (AUTOSTART).
  • Single side welding gun with various welding procedures like washer welding and wavy wire, etc…
  • Higher productivity, since reduced time in removing individual parts of a car for repair.
  • Heavy duty transformer for prolonged duty cycle.
  • Repair the panels outer to outer with out removing internal parts like power windows, auto-lock, wiring etc.
  • Portable system on trolley ,convenient to move all around the shop floor.
  • Wavy wire and washer welding for running board and step panel repairs.
  • High productivity with direct profitability.
  • User-friendly.
  • This field is for validation purposes and should be left unchanged.

ATS ELGI Flatliner is a complete system for repairing body panels . It allows you to work from outside without removing the parts . It significantly speeds up the worktime and enables you to repair the original body panel without replacement. Major panel dents can be fixed using flatliner.

Applications

  • Suitable for all models of passenger cars
  • SUV and MPV
  • Repairs new generation HSS steel
  • Sliding hammer
  • FL 80 with pair of single feet
  • FL 120 with pair of double feet
  • FL 160 with pair of single feet
  • Inno puller
  • Welding bits and hammers
  • This field is for validation purposes and should be left unchanged.

Twister – dust extraction are used in garages and in assembly line. The TWISTER is fixed to the wall by means of a supporting bracket and is normally connected to a jointed arm (Pinocchio series) or to a wall-mounted or fixed E.P. control unit by means of a pipe protected by a channel.
The unit is switched on and off by the two gate valves located below the control unit (wall-mounted, fixed or part of the arm).The hoses for extraction of dust from sanding machines or for internal cleaning of vehicles are connected to these gate valves.
When operating, the turbine located above the chamber extracts the dust produced during sanding of primers, resins or similar.The dust is then channeled via the extraction pipe into the chamber and, via the needle felt filter and cyclone, is deposited in the dust container Periodically, according to the type of dust or particles extracted and the frequency of use, the user must empty the dust container into the collecting bin.

Applications

  • Suitable for dry sanding applications in both garages and assembly line
  • Different arm lengths avaliable (6m , 7m , 8m)
  • High suction capacity – 100 m3/h
  • Articulated type arm
  • Automatic filter cleaning
  • 3 phase/1 phase socket available
  • FRL unit available
  • 2 air connections available
  • Ensures pollution free environment
  • Life time warranty on filters
  • This field is for validation purposes and should be left unchanged.

The portable dust extraction system collects the sanding dust in a container and the same can be disposed later. Handling and disposal of the sanding dust becomes easy making the work place clean and safe.

Applications

  • Suitable for dry sanding applications in both automotive bodyshops / garages
  • Carpentry works and industries
  • High suction capacity of 2.6 m3/min
  • Automatic on-off motor
  • Dual action sander
  • Simultaneous usage of dual sanders
  • Variable vacuum control
  • Long running filter
  • Thermal protection device: max. motor working heat 125 ° C
  • Low running costs
  • Ensures pollution free environment
  • HEPA filtration
  • This field is for validation purposes and should be left unchanged.

Infrared dryers are used in body shop for drying painted jobs with better quality at a very short time.In a traditional paint booth the hot air is made to pass on the jobs which will dry it from top-to-bottom. Due to this some moisture will remain inside the layers which will result in improper finish/short life of the job done. Whereas IR dryers uses short wave technology which heats the job from bottom-to-top so that the moisture inside each layer is eliminated which results in quick drying time and ensures long life for the painted jobs.

Applications

  • Suitable for automotive bodyshops / garages and industries
  • For drying putty,primer,paint and clear coat
  • For drying single panel jobs
  • Hydraulic lifter turning around 300 degrees
  • Short wave infra red technology
  • Automatic distance sensor
  • LED display with electronic timer
  • Can reach any part of the car including roof
  • Reduced drying time with low running cost
  • Safer, smarter and faster
  • Each lamp can be controlled separately
  • This field is for validation purposes and should be left unchanged.

Plasma cutter are used in body shop for cutting of metals. Plasma is nothing but fourth state of matter. Pressurized air is made to pass on the job , when the electrode (torch) comes in contact with the job an arc is produced which heats up the pressurized gas and creates plasma which is sufficient to cut the metal.

Applications

  • Suitable for all models of passenger cars , SUV and MPV
  • Suitable for jobs with 6 – 8 mm sheet thickness
  • Inverter technology
  • Equipped with power factor correction device
  • Pilot Arc to cut painted or coated metals
  • Cutting operation on superimposed thin sheets
  • Safety systems on the torch
  • Pilot arc starts without high frequency – so the machine can be operated next to electronic devices sensitive to high frequencies
  • Post-gas function
  • Electronic regulation of cutting current
  • Microprocessor-controlled cutting parameters and functions
  • Low power consumption
  • Precise cutting and removing of damaged parts
  • 4 metre-long P25 torch – comfortable to operate
  • Thermostatic protection
  • High duty cycle
  • This field is for validation purposes and should be left unchanged.

There is a shift in the trend of MIG MAG welders from transformers to inverter type as inverter welders have high welding power and low power consumption. Inverter technology reduces the size of the transformer and thus making the machine light weight.

Applications

  • Suitable to weld steel , stainless steel and aluminium
  • Suitable for automobile bodyshops/garages and industries
  • Welding of cut open body panels
  • Body parts can be joined together
  • Spot welding on areas where regular spot welders arm cannot reach
  • Dedicated control to fine tune the arc length
  • Equipped with power factor correction design
  • High quality torch for perfect finish
  • Support wire reels weighing 5 Kg and 300 mm dia
  • Wire feeder unit and cylinder stand are in standard scope
  • Automatic setting of welding parameters
  • High quality weld
  • Compact and light weight
  • This field is for validation purposes and should be left unchanged.

MIG – MAG welders is also known as Metal Inert Gas welding or Metal arc gas welding. They use a continuously fed wire electrode to form an arc and to provide filler metal. A shielding gas is used to shield the weld from atmospheric contamination and oxidation.This type of welding find its application to butt body parts together.

Applications

  • Suitable to weld steel , stainless steel and aluminium
  • Suitable for all models of passenger cars , SUV and MPV
  • Welding of cut open body panels
  • Body parts can be butt together
  • Spot welding on areas where regular spot welders arm cannot reach
  • Wire feeder unit and cylinder stand are in standard scope
  • High quality torch for perfect finish
  • Wire feed speed can be adjusted
  • Possibility to adjust welding current and time
  • Supports 15 Kg wire spool with 300 mm dia
  • Portable
  • This field is for validation purposes and should be left unchanged.